Konfigurasi Router Cisco 1 (Awal)

Konfigurasi Router Cisco 1 (Awal)
Konfigurasi Router Cisco 1 (Awal)

Konfigurasi Router Cisco 1 (Awal)

Konfigurasi Router Cisco 1 (Awal)
Konfigurasi Router Cisco 1 (Awal)

R-DPS#conf t

Enter configuration commands, one per line.  End with CNTL/Z.
R-DPS(config)#int fa0/0
R-DPS(config-if)#spe
R-DPS(config-if)#speed 100
R-DPS(config-if)#dup
R-DPS(config-if)#duplex full
R-DPS(config-if)#ba
R-DPS(config-if)#band
R-DPS(config-if)#bandwidth 100.000
^

% Invalid input detected at ‘^’ marker.

R-DPS(config-if)#bandwidth 100000
R-DPS(config-if)#q
^
% Invalid input detected at ‘^’ marker.

R-DPS(config-if)#^Z
R-DPS#sh ru
R-DPS#sh run
R-DPS#sh running-config int fa0/0
Building configuration…

Current configuration : 110 bytes!

interface FastEthernet0/0
bandwidth 100000
ip address 10.1.3.1 255.255.255.0
speed 100
full-duplex
end

R-DPS#sh int fa0/0

FastEthernet0/0 is up, line protocol is up
Hardware is Gt96k FE, address is c00d.0128.0000 (bia c00d.0128.0000)
Internet address is 10.1.3.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of “show interface” counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 1000 bits/sec, 2 packets/sec
29399 packets input, 2678701 bytes
Received 4423 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
5748 packets output, 465908 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets

R-DPS#de
R-DPS#debu
R-DPS#debug ?
IUA                       ISDN adaptation Layer options
aaa                       AAA Authentication, Authorization and Accounting
aal2_xgcpspi              AAL2_XGCP Service Provider Interface.
access-expression         Boolean access expression
acircuit                  Attachment Circuit information
adjacency                 adjacency
alarm-interface           Alarm Interface Card events
all                       Enable all debugging
archive                   debug archive commands
arp                       IP ARP and HP Probe transactions
asnl                      Application Subscribe Notify Layer
async                     Async interface information
backhaul-session-manager  Backhaul SM options
backup                    Backup events
bcm560x                   BCM560X L2 Driver
beep                      BEEP debugging
bgp                       BGP information
bing                      Bing(d) debugging
call                      Call Information
call-admission            Call admission control
call-mgmt                 Call Management
callback                  Callback activity

R-DPS#debug ip os
R-DPS#debug ip ospf
% Incomplete command.

R-DPS#debug ip ospf
% Incomplete command.

R-DPS#debug ip ospf ?
adj             OSPF adjacency events
database-timer  OSPF database timer
events          OSPF events
flood           OSPF flooding
hello           OSPF hello events
lsa-generation  OSPF lsa generation
mpls            OSPF MPLS
nsf             OSPF non-stop forwarding events
packet          OSPF packets
retransmission  OSPF retransmission events
spf             OSPF spf
tree            OSPF database tree

R-DPS#debug ip ospf he
R-DPS#debug ip ospf hello
OSPF hello events debugging is on
R-DPS#no debug ip ospf hello
OSPF hello events debugging is off
R-DPS#no debug ip ospf pac
R-DPS#no debug ip ospf packet
OSPF packet debugging is off
R-DPS#ter

R-DPS#terminal ?

autohangup              Automatically hangup when last connection closes
autoselect              Set line to autoselect
data-character-bits     Size of characters being handled
databits                Set number of data bits per character
default                 Set a command to its defaults
dispatch-character      Define the dispatch character
dispatch-timeout        Set the dispatch timer
domain-lookup           Enable domain lookups in show commands
download                Put line into ‘download’ mode
editing                 Enable command line editing
escape-character        Change the current line’s escape character
exec                    Configure EXEC
exec-character-bits     Size of characters to the command exec
flowcontrol             Set the flow control
full-help               Provide help to unprivileged user
help                    Description of the interactive help system
history                 Enable and control the command history function
hold-character          Define the hold character
international           Enable international 8-bit character support
ip                      IP options
length                  Set number of lines on a screen
modem                   Configure the Modem Control Lines

R-DPS#terminal

 

R-DPS#terminal mo
R-DPS#terminal mon
R-DPS#terminal monitor
R-DPS#debug ip ospf packet
OSPF packet debugging is on
R-DPS#terminal monitor
R-DPS#
*Mar  1 03:49:04.991: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
*Mar  1 03:49:14.963: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
*Mar  1 03:49:24.963: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
*Mar  1 03:49:34.947: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
R-DPS#no debug ip ospf packet
OSPF packet debugging is off
R-DPS#
*Mar  1 03:56:07.851: %OSPF-5-ADJCHG: Process 100, Nbr 10.100.100.2 on Serial0/0 from FULL to DOWN, Neighbor Down: Dead timer expired
R-DPS#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R-DPS(config)#no ro
R-DPS(config)#no router ospf
% Incomplete command.

R-DPS(config)#no router ?
bgp       Border Gateway Protocol (BGP)
eigrp     Enhanced Interior Gateway Routing Protocol (EIGRP)
isis      ISO IS-IS
iso-igrp  IGRP for OSI networks
mobile    Mobile routes
odr       On Demand stub Routes
ospf      Open Shortest Path First (OSPF)
rip       Routing Information Protocol (RIP)

R-DPS(config)#no router os
R-DPS(config)#no router ospf 100
R-DPS(config)#router ospf 100
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
R-DPS(config-router)#net
*Mar  1 03:58:51.095: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
*Mar  1 03:59:01.115: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#
*Mar  1 03:59:11.051: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#no router ospf 100
R-DPS(config)#router ospf 100
R-DPS(config-router)#net 10.100.100.4 0.0.0.0 area 1
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
*Mar  1 04:00:01.111: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
*Mar  1 04:00:11.131: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.6 0.0.0.0 area 1
*Mar  1 04:00:21.071: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.6 0.0.0.0 area 1
R-DPS(config-router)#end
R-DPS#
*Mar  1 04:00:29.611: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)
R-DPS#
*Mar  1 04:00:31.087: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar  1 04:00:41.111: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar  1 04:00:51.075: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar  1 04:01:01.091: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar  1 04:01:11.095: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar  1 04:01:21.075: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R-DPS(config)#router ospf 100
R-DPS(config-router)#pas
R-DPS(config-router)#passive-interface
*Mar  1 04:01:31.107: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#passive-interface fa
R-DPS(config-router)#passive-interface fastEthernet 0/0
R-DPS(config-router)#sh ip ospf ne
R-DPS(config-router)#exit
R-DPS(config)#exit
R-DPS#
*Mar  1 04:03:21.786: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)
R-DPS#sh ip ospf neigh
R-DPS#sh ip ospf neighbor

Sumber : https://duniapendidikan.co.id/